295/65R20 tire size
295mm wide with a 65% aspect ratio on a 20-inch wheel — 35.1 inches tall overall. Below: what it measures, what it swaps with, and which trucks run it from the factory.
Sizes that swap with 295/65R20
Within 3% of the original diameter — close enough to fit without a recalibration or clearance work on most trucks.
| Size | Diameter | Difference | Width |
|---|---|---|---|
| 35x12.50R16 | 35.00" | -0.10" (-0.3%) | 12.5" |
| 35x12.50R17 | 35.00" | -0.10" (-0.3%) | 12.5" |
| 35x12.50R18 | 35.00" | -0.10" (-0.3%) | 12.5" |
| 35x12.50R20 | 35.00" | -0.10" (-0.3%) | 12.5" |
| 35x12.50R22 | 35.00" | -0.10" (-0.3%) | 12.5" |
| 325/60R20 | 35.35" | +0.26" (+0.7%) | 12.8" |
| 325/50R22 | 34.80" | -0.30" (-0.9%) | 12.8" |
| 315/75R16 | 34.60" | -0.50" (-1.4%) | 12.4" |
Plus and minus sizing
Same overall height on a different wheel. Going down a wheel size buys sidewall for off-road; going up is usually about looks. Gearing and speedometer stay put either way.
Compare 295/65R20 against your current size
Tire size comparison
Diameter change, speedometer error, and whether it will rub.
35.1" tall · 11.6" wide ·
35.0" tall · 12.5" wide
Large enough that rubbing at full steering lock or under suspension compression is common. Usually solved by removing the front mud flaps or trimming the air dam.
- Sits 0.05" lower at the axle.
- 0.89" wider overall, so roughly 0.44" more on each side unless you change wheel offset.
Reading this size
295/65R20 breaks down as 295mm section width, an aspect ratio of 65 (the sidewall is 65% of the width, so 7.55 inches), and a 20-inch wheel. Overall diameter is the wheel plus two sidewalls: 20 + 7.55 + 7.55 = 35.10 inches.
That last figure is the one that matters when you change size. The speedometer, odometer, transmission shift points and stability control all assume the factory diameter, so staying within a few percent keeps everything calibrated. Width matters for clearance rather than gearing — it decides whether the tire touches the suspension at full lock.
Common questions
How tall is a 295/65R20 tire?
35.10 inches in overall diameter, with a 7.55-inch sidewall on a 20-inch wheel. Section width is 11.61 inches (295mm), and it turns about 575 times per mile. Real tires vary from the nominal figure by up to half an inch depending on brand and tread.
What is equivalent to a 295/65R20?
The closest common size is 35x12.50R16 at 35.00 inches — -0.3% different. Anything within about 3% of the original diameter swaps on without upsetting the speedometer badly or needing a tune.
Will 295/65R20 fit my truck?
We do not have it listed as a factory size on the trucks we cover, so treat it as an upgrade size. Put your current size into the calculator on this page to see the diameter change and whether it is likely to rub.
Does going to 295/65R20 affect my speedometer?
Only if the overall diameter changes. The speedometer counts wheel rotations and multiplies by the factory tire circumference, so a larger tire makes the truck travel further per rotation than the gauge assumes and the display reads low. Around 3% is where transmission shift points and stability control calibration start to matter, and most modern trucks can be recalibrated for the new size.